Easa module 7 essay

Easa module 9 essay questions and answers pdf

Describe the procedure for towing an aircraft from the hangar to the line, including all safety aspects. Discuss the precautions you would take, before during and after a windscreen replacement. Describe the procedures when inspecting a brake unit. Besides those 2 important factors, i would also take into accounts things like time constraints, spares availability and manpower constraints. Introduction Tool control within a part maintenance organisation can be divided in two main areas, the control of company supplied tools and the individual control of their own personal tooling. Personnel should be wearing any personal protective equipment like mask, goggles, gloves, etc that is required by the particular job. Describe the procedures and equipment used to return the aircraft to service. Leaving it alone If after performing my inspection and with reference to the applicable manuals, i determine that the corrosion is minor and does not require any further work, i would remove the corrosion using the. Aims of the Module P. About 74, District residents under age 65 did not have health insurance coverage at some time during the year. Essay on module 7 Mod 7 Final Assignment I decided to report about an unacceptably high number of District of Columbia residents that lack health insurance. Attendance and Punctuality p.

The pilot reports a burning smell from the flight deck air conditioning system. Describe the procedure of a hold-over item Describe how you would make a hole in metal, composite and wood, discuss this in context of aircraft maintenance, state the precautions to be taken and include any limits or tolerances that the usage of these tools can achieve You notice that there is no hydraulic pressure indicated on the left system, details your actions.

Easa module 7 essay questions writing pattern

Late Submission p. Give details of defects it will find, what materials the techniques may be used on and what are the chief advantages and disadvantages of each technique There is 2 inches of wet snow on the aircraft, the temperature is —2oC, what are your considerations before releasing the aircraft for departure? During an engine start it is noticed that the No. You are required to carry out a bonding test on an aircraft. Key Texts p. E-tests and the E-final Final Grades have? Describe the procedures when inspecting a brake unit. List down the types of engineering drawing. Describe how tooling and equipment is controlled within a part maintenance organisation. You notice that there is no hydraulic pressure indicated on the left system, details your actions. Label all inputs and outputs and highlight your final answer. List NDT techniques commonly used for inspecting aircraft structure and components. Disassemble the connector to detect corrosion.

Describe how tooling is controlled within a Part maintenance organization. Academic Misconduct p.

Easa module 1 question bank

There is water contamination in the fuel tank, how would you carry out a water fuel contamination test and what are the other tests you could carry out, describe any follow-up actions if contamination is found and continues in the future. Key Texts p. The library also has a Special Collections Department that has rare books and is the home of several national archives. On trouble shooting an IDG overheat lamp fault, it was discovered that the connector of the IDG had evidence of overheating. The Health Care Coverage Advisory Panel has issued eight recommendations for expanding health insurance in the District. Neoclassical artists emphasized firm lines, clear structure, and moralistic subject matter. List down the types of engineering drawing. Discuss the precautions you would take, before during and after a windscreen replacement. Describe the procedure for weighing an aircraft. So it requires be written in points.

During an engine start it is noticed that the No. Describe how tooling and equipment is controlled within a part maintenance organisation.

easa module 13 question bank pdf

On a major hangar inspection, you find corrosion on a panel on an unpressurised area of the fuselage, detail your actions to return the aircraft to service. C R S w o u l d b e i s s u e d b y a appropriately authorized engineer and a statement would be made in the technical log to monitor the systems affected on the next flights.

easa part 66 question bank pdf

Related Searches. List down the types of fire extinguishers. Describe how you would make a hole in metal, composite and wood, discuss this in context of aircraft maintenance, state the precautions to be taken and include any limits or tolerances that the usage of these tools can achieve.

Describe the procedure to refuel a medium sized passenger jet Include all safety checks that should be observed. Related Interests.

Easa module 7 essay

Describe how you would replace an electronics card, and the precautions you would take. Describe how you would make a hole in metal, composite and wood, discuss this in context of aircraft maintenance, state the precautions to be taken and include any limits or tolerances that the usage of these tools can achieve. Click on the links to view the answers of these module 7 Essay questions. How is safety in the aircraft hangar achieved? Academic Misconduct p. I would attempt to isolate the fault, debrief t h e a i r c r e w, i f necessary and confirm it is HIRF and not just a fault with the systems involved. I would then determine the type of corrosion. What inspections would you carryout to it during servicing?
Rated 7/10 based on 26 review
Download
Module 7 Essay Questions